Aluminum casthouses are under pressure to raise the share of post-consumer recycled (PCR) aluminum in their furnaces without sacrificing melt quality, metal recovery or production efficiency. Much of that material arrives as lightweight scrap, machining chips and other low-density fractions that are awkward to charge into conventional melting furnaces, which makes efficient scrap feeding and submergence central to recycling performance.
The problem does not stop at scrap preparation. Temperature and chemical composition must stay consistent through the whole molten bath to hit specification, so circulation and stirring equipment has to deliver heat transfer and metal movement while limiting process interruptions and excess metal loss. Conventional mechanical pumps, although widely used, depend on immersed rotating components that deteriorate through contact with molten aluminum, dross accumulation and refractory debris.
Where the magnetic approach comes from
Zmag America, Ltd. works in that specialised corner of casthouse technology, developing magnetic engineering for molten-metal circulation, furnace stirring and scrap recovery. Its roots lie in the industrial application of magnets and magnetic circuits, including commercialisation of eddy-current separation for recovering non-ferrous metals from mixed material streams. The company later extended its focus to molten-metal duties and developed its patented zPMC (Zmag Permanent Magnetic Circuit) as the foundation for equipment that stirs, circulates and submerges material in molten aluminum.
The distinction that matters is between permanent-magnet and conventional electromagnetic systems. Instead of a conventional electromagnetic stirring arrangement, zPMC uses a permanent magnetic circuit to generate the field that moves the metal. Zmag describes the resulting movement as a virtual impeller: circulation is produced without a conventional immersed mechanical impeller in the bath.
Familiarity, rather than physics, has been a practical obstacle in some markets. In an August 2025 interview with AL Circle, Eishin Takahashi, president of Zmag America, identified limited familiarity with the technology as one barrier to wider adoption in the United States, observing that aluminum producers globally tend to be conservative and more comfortable with equipment and processes they already know.
MagStir: non-contact stirring for furnace homogenisation
MagStir is a non-contact stirring system for aluminum melting and holding furnaces. The permanent magnetic circuit drives movement within the bath to homogenise temperature and alloy composition. Zmag offers configurations for furnaces with capacities from 15 to 200 metric tons, and because there is no immersed mechanical stirring component, the system is positioned as a way to improve melt circulation without adding moving parts to the molten-metal environment.
The installation record extends beyond the United States. New Zealand Aluminium Smelters (NZAS) fitted the technology to a casting furnace and later extended its use to additional furnaces; a technical case study published in 2017 examined those installations and reported improvements in temperature control during furnace preparation. At Rio Tinto-operated Boyne Smelters in Queensland, Australia, a MagStir unit was fitted to a casthouse furnace in 2019.
MagPump: circulation without a physical impeller
MagPump extends the same magnetic engineering to molten-metal pumping and circulation. The system is designed to fit a standard pump well without requiring furnace modification. It has no physical impeller and is marketed as a nearly hands-free alternative with no consumable parts and minimal downtime.
TST Inc., a US secondary aluminum producer, examined the system at the TANDEM Division of its Fontana, California, plant. Over a seven-week trial, MagPump replaced an existing mechanical pump in a furnace used for aluminum production. The reported findings describe smooth operation and reduced disturbance of the molten-metal surface; plant management also reported that the system avoided the splashing experienced with conventional pumping as the furnace metal level fell during draining.
The technology was presented at the TMS 2023 Annual Meeting and Exhibition, where its application in side-well, multi-chamber furnaces was discussed. That presentation also set out potential duties beyond primary circulation, including gas injection and scrap submergence.
Typhoon: pulling light scrap beneath the surface
Typhoon targets scrap submergence and chip melting, introducing lightweight scrap and machining chips beneath the molten-metal surface rather than letting them remain on top of the bath. Its magnetic circuit generates a vortex-like movement that draws material into the melt, supporting heat exchange and recovery during remelting.
The clearest recent reference point is Neuman Aluminium's Marktl facility in Austria, where a Typhoon chip-submergence system was incorporated into a furnace modernisation intended to widen the plant's ability to process low-density post-consumer scrap. The targeted fractions had a bulk density of approximately 375 kg/m³ and had presented challenges for conventional furnace charging and melting.
Reported operating results exceeded the initial expectation. Neuman had set a target of processing one metric ton per hour while continuing to melt solid charge materials in the same furnace; in operation the Typhoon system processed almost twice the planned scrap quantity within the expected time, without disrupting normal furnace operations. The company also reported low operator involvement and no negative impact on melt or finished-product quality.
According to the published technical account, Typhoon operates at 5–15 kW including its air-cooling blower and can submerge up to five metric tons per hour of machining chips. Vortex intensity can be adjusted to suit operating requirements, allowing the system to maintain molten-metal movement when scrap or alloying material is not being charged.
A crowded field that is not equivalent
The market for aluminum furnace stirring, molten-metal circulation and scrap-submergence equipment includes several established industrial suppliers, although their offerings do not all represent direct equivalents to a permanent-magnet system.
ABB supplies its AL-EMS electromagnetic stirring system for melting, holding and alloying furnaces, with a global installation base the company puts at more than 430 units. In April 2026 ABB announced a further order from Arconic for a fifth stirrer at its Hungarian casthouse, following earlier installations at the same facility.
Presezzi Extrusion Group, through its Melting Technology division and North American presence, competes in the furnace-stirring segment with its L.E.C. (Low Energy Consumption) Stirrer for melting and holding furnaces, alongside equipment for aluminum remelting and complete casthouse operations.
Pyrotek spans a broader range of casthouse equipment, including electromagnetic pump systems and its LOTUSS (Low Turbulence Scrap Submergence) technology. Its EMP systems use electromagnetic forces to circulate molten aluminum and support metal transfer and scrap charging, while LOTUSS uses a circulation pump and refractory well to submerge lightweight scrap. Pyrotek's UK operations include EMP Technologies Ltd., involved in the design, sale and installation of metal-melting and circulation systems incorporating electromagnetic pumps.
Rockwell Automation sits in the adjacent industrial automation segment rather than offering a like-for-like permanent-magnet stirring product; its aluminum work includes furnace and ladle-shop control systems, as demonstrated by its modernisation project for Mozal Aluminium's casthouse operations.
What the evidence settles and what it leaves open
The public evidence for magnetic, non-immersed equipment is still largely company-reported and case-study scale: a 2017 case study, a 2019 installation, a seven-week pump trial and one chip-submergence project. That is enough to show the approach functions in specific furnaces and duty cycles; it is not enough to settle how it performs across a full casthouse campaign or how it compares with every established alternative on consumable cost, refractory life and metal loss.
Even so, the direction of the argument is visible. As producers take on more challenging recycled feedstock, the ability to manage molten-metal movement without conventional immersed mechanical components is likely to become an increasingly relevant consideration for casthouse operators weighing equipment choices.
